166 10/02 kal0567 b accessories for capacitors with mounting stud on capacitor base capacitor diameter dimensional drawing diameter d (mm) ordering code insulating plastic shoulder washer ?p? similar to din 41 331 specifications 40 mm for m 8 thread 8,4 B44020b0001b025 > 40 mm for m 12 thread 12,5 B44020b0002b030 insulating washer ?n? made of laminated paper 40 mm for m 8 / m 12 thread 8,4 B44020a0001b025 > 40 mm 13 ,0 B44020a0002b025 insulating washer made of hostalen 51,6 mm 76,9 mm B44020b0006b051 B44020b0006b076 kal0216-i kal0059-p kal0066-7 kal0061-1 d 1 0,5 d 2 0,5 51 31 76 56 accessories B44020 accessories
167 10/02 kal0567 b *) for achieving larger clearances. capacitor diameter dimensional drawing ordering code plastic cap nut ?v? 40 mm for m 8 thread width across flats 13 mm B44020b0005b008 > 40 mm for m 12 thread width across flats 17 mm B44020a0005b012 reinforced nylon cap nut > 40 mm for m 12 thread width across flats 19 mm B44020j0006b012 40 mm for m 8 thread width across flats 17 mm B44020j0006b008 > 40 mm for m 12 thread *) width across flats 19 mm B44020j0007b012 kal0067-f kal0068-n kal0236-x kal0285-q accessories B44020
168 10/02 kal0567 b mounting instructions maximum tightening torques: thread maximum torque m8 m12 4nm 10 nm non-insulated mounting with cap nut insulated mounting with cap nut insulated mounting with din 439 hex nut d 76,9 mm d = 91 mm kal0063-h mounting hole diameter kal0064-q mounting hole diameter mounting hole diameter kal0065-y accessories B44020
169 10/02 kal0567 b ring clip mounting ring clips are primarily used for upright mounting of screw-terminal and photoflash capacitors. the clip surfaces are specially treated and corrosion-protected. a variety of ring clip versions is available for al electrolytic capacitors. some versions are supplied with am 3 10 din 84 clamping screws and din 934 nuts included. additional insulation can be achieved by inserting a 30 mm-wide insulating strip between the capacitor and the ring clip. in such cases, attention must be paid to any relevant regulations (e. g. vde, bsa or ul regulations). d n h 1 h 2 ring clip version ordering code without with mm insulating strip 25 19 15 clamping screws and nuts are included in delivery package. b44030a0025b b44030j0025b (insulating strip length:175mm) 30 19 15 clamping screws and nuts are included in delivery package. b44030a0030b b44030j0030b (insulating strip length: 200mm) kal0193-a mounting plate capacitor d n kal0198-g kal0199-p accessories b44030
170 10/02 kal0567 b d n h 1 h 2 ring clip version ordering code without with mm insulating strip 35 19 15 clamping screws and nuts are included in delivery package. b44030a0035b b44030j0035b (insulating strip length: 230mm) 15 10 b44030a0036b b44030j0036b (insulating strip length: 230mm) 40 19 15 clamping screws and nuts are included in delivery package. b44030a0040b b44030j0040b (insulating strip length: 260mm) kal0201-5 kal0200-w accessories b44030
171 10/02 kal0567 b d n h 1 h 2 ring clip version ordering code without with mm insulating strip 50 19 15 clamping screws and nuts are included in delivery package. b44030a0050b b44030j0050b (insulating strip length: 325mm) 22 15 b44030a0051b b44030j0051b (insulating strip length: 325mm) 65 26 22 clamping screws and nuts are included in delivery package. b44030a0065b b44030j0065b (insulating strip length: 420mm) kal0194-i kal0203-l accessories b44030
172 10/02 kal0567 b d n h 1 h 2 ring clip version ordering code without with mm insulating strip 65 29 19 b44030a0064b b44030j0064b (insulating strip length: 420mm) 75 29 19 b44030a0075b b44030j0075b (insulating strip length: 495mm) 90 29 19 b44030a0090b b44030j0090b (insulating strip length: 585mm) accessories b44030
173 10/02 kal0567 b clamp mounting screw-terminal capacitors without threaded stud and with a diameter 64,3 mm can also be mount- ed with clamps. clamp mounting offers the following advantages: optimum heat transfer between capacitor base and board due to pressure contact high vibration resistance electrically insulated material dimensional drawing dimensions and ordering codes screws are not included in the delivery package. capacitor diameter d n d 1 0,2 mm b mm ordering code 65 mm 87 104 b44030a0165b 75 mm 99 116 b44030a0175b 90 mm 112 130 b44030a0190b capacitor fixing part board section a-b untightened tightened cylinder screw din912-m6x d n tubular rivet 3) 1) lenght depends on application. 2) the screws have to be tightened uniformly and crosswise until the fixing part rests flatly on the board. 3) tubular rivets included in delivery package. accessories b44030
174 10/02 kal0567 b mounting set (clamping rings) this mounting set offers following advantages: protects the capacitor against tilt fits for different capacitor length protects the capacitor terminals from mechanical stress electrically insulated clamping material dimensional drawing kal0499-8 101 90 95,5 57,5 63.5 120 ? 105 120 75 86 83 12 45,5 86 10 43,5 80 5 6 mounting base plate clamping ring min. kal0499-8 dimensions and ordering codes capacitor diameter d n ? min mm ordering code 75 mm 84 b44030a0375b 90 mm 96,5 b44030a0390b accessories b44030
herausgegeben von epcos ag unternehmenskommunikation, postfach 80 17 09, 81617 mnchen, deutschland ++49 89 636 09, fax (0 89) 636-2 26 89 ? epcos ag 2002. vervielf?ltigung, ver?ffentlichung, verbreitung und verwertung dieser broschre und ihres inhalts ohne aus- drckliche genehmigung der epcos ag nicht gestattet. bestellungen unterliegen den vom zvei empfohlenen allgemeinen lieferbedingungen fr erzeugnisse und leistungen der elek- troindustrie, soweit nichts anderes vereinbart wird. diese broschre ersetzt die vorige ausgabe. fragen ber technik, preise und lieferm?glichkeiten rich ten sie bitte an den ihnen n?chstgelegenen vertrieb der epcos ag oder an unsere vertriebsgesellschaften im ausland. bauelemente k?nnen aufgrund technischer erfordernisse gefahrstoffe ent- halten. ausknfte darber bitten wir unter angabe des betreffenden typs ebenfalls ber die zust?ndige vertriebsgesellschaft ein - zuholen. published by epcos ag corporate communications, p.o. box 80 17 09, 81617 munich, germany ++49 89 636 09, fax (0 89) 636-2 26 89 ? epcos ag 2002. reproduction, publication and dissemination of this brochure and the information contained therein without epcos? prior express consent is prohibited. purchase orders are subject to the general conditions for the s upply of products and services of the electrical and electronics industry recommended by the zvei (german electrical and el ectronic manufacturers? associ ation), unless otherwise agreed. this brochure replaces the previous edition. for questions on technology, prices and delivery please contact the sales offices of epcos ag or the international representa- tives. due to technical requirements components may contain dangerous substances. for information on the type in question please also contact one of our sales offices.
|
